焚燒爐燃燒器常見故障

作者: 2013年07月18日 來源: 瀏覽量:
字號:T | T
1、燃燒器不能啟動了,是何道理? a、爐內光線強烈及其它地方有光透入到燃燒器光敏管,應及時排除泄漏。 b、無電源輸入。 c、程控器損壞。 d、油路堵塞 2、燃燒器,點火失靈應該怎么辦? a、第一次或油位低時點火,
焚燒爐燃燒器常見故障

1、         燃燒器不能啟動了,是何道理?

a、   爐內光線強烈及其它地方有光透入到燃燒器光敏管,應及時排除泄漏。

b、  無電源輸入。

c、  程控器損壞。

d、  油路堵塞

2、燃燒器,點火失靈應該怎么辦?

a、   第一次或油位低時點火,油管含空氣首次點火可能不成功,需在點火不成功后20秒按復位鍵重新啟動燃燒器,有時可能以上動作要進行幾次。

b、  燃料過濾器堵塞,應及時清洗過濾器。

c、  油壓不合理,霧化不好,調整出口壓力至10-12Kgf/cm2。

d、  電磁閥失靈了,檢修或更換。

e、   點火電極距離太遠,重新調整至3-5mm。

f、    點火變壓器故障,及時更換。

 

3、燃燒器故障表格分析

3. Burner fault

 

故障現象

Fault phenomenon

可能的原因

Possible reason

解決辦法

Solution

燃燒器不啟動

Burner does not start

無電源

no power supply

檢查電源 LN線之間的電壓220V是否存在

Check the power supply voltage between LN Line the existence of 220V

檢查保險絲的情況

Check the fuses

復位鈕紅燈亮

燃燒器鎖定

Reset button the red light

 Burner lock

重新按復位按鈕

Re-press the reset button

光電管感受到光線

Phototube feel light

消除光源

The elimination of the light source

控制盒的接線錯誤

Control box wiring error

檢查并重接

Inspection and re-wiring

在預吹掃及點火周期,燃燒器運行正常,但5秒后鎖定

In the pre-purge and ignition cycle, the burner is running normal, but five seconds later the lock

光電管臟

光電管壞

Phototube dirty

Phototube bad

清洗

更換

Cleaning

 Replacement

脫火或熄火

From fire or flameout

檢查泵壓力及燃料的輸出

Check the pump pressure and fuel output

檢查風量

Check the air flow

更換噴嘴

Replacement nozzle

檢查電磁閥線圈

Check the solenoid valve coil

燃燒器啟動并有點火延遲

Burner start and ignition delay

點火電極位置不對

Ignition electrode wrong location

按手冊的說明進行調節

According to the instructions manual adjustment

噴嘴臟或損壞

Nozzle dirty or damaged

更換

change

燃燒器啟動運行一段時間后熄火

Burner start running some time and then flameout

油路閥門未開

油路過濾器堵塞

油箱缺油

Oil valve is not open

 Oil filter plug

Oil tank oil less

打開閥門

清洗過濾器

油箱加滿油

Open valve

Cleaning filter

Top up oil

燃燒器點火后火焰不穩定

After the ignition burner flame instability

點火電極位置

Ignition electrode position

按手冊的說明進行調節

According to the instructions manual adjustment

油泵壓力低

Oil pump low pressure

一般出廠設置為12bar

General  set to 12bar

全球化工設備網(http://seenwhilewandering.com )友情提醒,轉載請務必注明來源:全球化工設備網!違者必究.

標簽:

分享到:
免責聲明:1、本文系本網編輯轉載或者作者自行發布,本網發布文章的目的在于傳遞更多信息給訪問者,并不代表本網贊同其觀點,同時本網亦不對文章內容的真實性負責。
2、如涉及作品內容、版權和其它問題,請在30日內與本網聯系,我們將在第一時間作出適當處理!有關作品版權事宜請聯系:+86-571-88970062